Ways To Reduce The Effect of Torque Steer
- Employ the use of a tire with proper sidewall ply design, mitigating the sidewall deformation.
- Have both driveshafts of the equal length by using an intermediate shaft (or "lay shaft") on one side of the transmission. This is already implemented on most modern cars. When the driveshafts have different length and excessive torque is applied, the longer half shaft flexes more than the shorter one. However, this is a short term transient effect. To avoid fatigue failure, the amount of drive shaft torsional deflection must necessarily be small. Effects due to one wheel spinning more slowly than the other are usually negligible. Equal lengths of the driveshafts, in the case of no asymmetric suspension deflection due to roll or bump, keep the drive shaft angles equal. The main component of torque steer occurs when the torques in the driveshaft and the hub are summed vectorially, giving a resultant torque vector around the steering pivot axis (kingpin). These torques can be substantial, and in the case of shafts making equal angles to the hub shafts, will oppose one another at the steering rack, and so will cancel. These torques are strongly influenced by the position of the driveshaft universal joint (CV joint) in relation to the steering axis, however due to other requirements such as achieving a small or negative scrub radius an optimum solution is not generally possible with simple suspension configurations such as Macpherson strut.
- Equalise the torque better between the driveshafts by using a low friction differential. The torque difference is zero if the differential is frictionless, and limited slip differentials, intended to increase power transfer, actually make torque steer much worse. For this reason, limited slip differentials by automobile transmission manufacturers like Quaife, Torsen, TrueTrac, Gold Trac have not been much used until recently, and require other measures to be implemented, such as careful positioning of suspension pivot points and driveshaft CV joints, in order to keep the resultant torque steer to a manageable amount. Limited slip differentials do not improve cornering, or steering feel, however they will improve power transfer in situations where one wheel experiences limited adhesion, and so may improve overall performance.
- Reduce the amount of torque from the front axle by passing part of torque to the rear axle. This is achieved on all-wheel-drive (AWD) vehicles with full-time AWD, e.g. with mechanical gear-based transaxle differential, e.g. Audi AWD cars equipped with Torsen transaxle differential.
- Power assisted steering (set on most modern cars) make the torque steer effect less noticeable to the driver. Steer-by-wire also hides the effect of torque steer from the driver. EPAS can be calibrated to directly suppress the torque effect at the handwheel, and the steer effect on the vehicle.
Rear-wheel-drive vehicles still are affected by torque steer in the sense that any of the above situations will still apply a steering moment to the car (though from the rear wheels instead of the front). However, the torque-steer effect at the rear wheels will not send any torque response back through the steering column, so the driver will not have to fight the steering wheel.
Read more about this topic: Torque Steering
Famous quotes containing the words ways to, ways, reduce, effect, torque and/or steer:
“It would be naive to think that peace and justice can be achieved easily. No set of rules or study of history will automatically resolve the problems.... However, with faith and perseverance,... complex problems in the past have been resolved in our search for justice and peace. They can be resolved in the future, provided, of course, that we can think of five new ways to measure the height of a tall building by using a barometer.”
—Jimmy Carter (James Earl Carter, Jr.)
“Imagination could hardly do without metaphor, for imagination is, literally, the moving around in one’s mind of images, and such images tend commonly to be metaphoric. Creative minds, as we know, are rich in images and metaphors, and this is true in science and art alike. The difference between scientist and artist has little to do with the ways of the creative imagination; everything to do with the manner of demonstration and verification of what has been seen or imagined.”
—Robert A. Nisbet (b. 1913)
“I’ve tried to reduce profanity but I reduced so much profanity when writing the book that I’m afraid not much could come out. Perhaps we will have to consider it simply as a profane book and hope that the next book will be less profane or perhaps more sacred.”
—Ernest Hemingway (1899–1961)
“Ignorant kindness may have the effect of cruelty; but to be angry with it as if it were direct cruelty would be an ignorant unkindness.”
—George Eliot [Mary Ann (or Marian)
“Poetry uses the hub of a torque converter for a jello mold.”
—Diane Glancy (b. 1941)
“A great deal of us is together, and we can but abide by it, and steer our courses to meet soon. John Thomas says goodnight to Lady Jane, a little droopingly, but with hopeful heart.”
—D.H. (David Herbert)