Contax - Historical Overview

Historical Overview

While the firm of Ernst Leitz of Wetzlar established the 24 mm × 36 mm negative format on perforated 35 mm movie film as a viable photographic system, Zeiss Ikon of Dresden decided to produce a competitor designed to be superior in every way. The name Contax was chosen after a poll among its employees. Dr. Ing. Heinz Küppenbender was its chief designer.

Made between 1932 and 1936, the original Contax, known as Contax I after later models were introduced, was markedly different from the corresponding Leica. Using a die-cast alloy body it housed a vertically travelling metal focal-plane shutter reminiscent of the one used in Contessa-Nettel cameras, made out of interlocking blackened brass slats somewhat like a roll-up garage door. This complex shutter became the characteristic of the Contax camera and its Super-Nettel derivative. By contrast, the competitive Leica followed the established design of using rubberized fabric shutter curtains wound around rollers, moving horizontally. The Contax design allowed a higher maximum shutter speed: the top speed was 1/1000s, then increased to 1/1250s in the Contax II. The fact the shutter ran across the shorter dimension of the format area was a significant factor for achieving this technical feat. The interlocking slats were aligned by specially woven silk ribbons, which were very strong but subject to wear. Replacing these ribbons was very difficult. But contrary to modern cameras made for a 400,000-cycle life. Zeiss invented also the System Camera, with all sorts of near-photo, wide-angle, mirror-house, long-focal-length lenses for specific situations. However Zeiss called it Universalkamera. One of the key design features was a coupled rangefinder with a very long baseline, with its own eyepiece next to that of the viewfinder. To enhance accuracy, a novel rotating wedge system was employed in lieu of the common swinging mirror mechanism. Other main features included focusing drive built into the camera body for use with standard lens, removable back, shutter-speed knob integral with film-wind knob placed at the front of the camera body, and black-enamelled finish.

The young lens designer Ludwig Bertele, formerly of Ernemann, was charged with the responsibility of designing the lenses. It can be said that with a few exceptions, Contax lenses were superior to equivalent contemporary Leica lenses for more than two decades. The greatest advantage of the Zeiss lenses was the reduced number of air-to-glass surfaces in Bertele's designs. In the years before lens coating was generally practiced, this had advantages for contrast and resistance to lens flare. Zeiss pioneered in glass coating too and before the war coated lenses were offered. After lens coating became universal post WW2, designers were given more freedom in using extra air-to-glass surfaces in correcting lens aberrations, without fear of the ill effects of surface reflections.

In 1936 the Contax II and III models were introduced; the only difference between them was the integral exposure meter on the latter model. They introduced the combined eyepiece for both viewfinder and rangefinder, the shutter speed and film wind knob placed on the top plate, fastest shutter speed at 1/1250 s. and finished in chrome plating. They became very popular among professional photographers, especially photojournalists who demanded high-performance, large-aperture lenses for available-light work and a workhorse. The vertical shutter had both variations in speed, slit and a break that was again a Zeiss first.

After the Second World War, a few Contax cameras were produced at the original Dresden factory, and some were assembled at the Carl Zeiss optical works at Jena, before production was transferred to Kiev in Ukraine. During the war years, the chief designer, Hubert Nerwin, tried to convert the Contax into a single-lens reflex camera but was hindered by the presence of the upper roller of the vertical focal-plane shutter. The postwar design chief Wilhelm Winzenberg started with a clean slate, which became the Contax S (Spiegelreflex), even though the "S" was not marked on the camera.

The Contax S can be said to be the camera that defined the configuration of the modern 35mm SLR camera. Not only did it introduce the M42 lens mount which became an industry standard, but it was also equipped with a horizontal focal-plane shutter, and also removed a major objection against the reflex camera by offering an unreversed, eye-level viewing image by employing a pentaprism. Introduced in 1949, numerous models followed including D, E, F, FB, FM and FBM. During that period, VEB Zeiss Ikon, as the firm became known, was gradually under pressure from the new Zeiss Ikon AG in the US zone, so the original Zeiss Ikon and Contax names and trademarks gradually disappeared and were replaced by the new name of Pentacon, which never really caught on. Finally this line of camera was abandoned.

Meanwile in the US zone, the three main Zeiss concerns – Carl Zeiss Stiftung (Carl Zeiss Foundation), Carl Zeiss optical, and Zeiss Ikon – were reestablished. With Hubert Nerwin in charge as design chief, heavily revised Contax models, the IIa and IIIa, were produced at the new Zeiss Ikon plant at Stuttgart, and they were made until 1962.

With the emergence of the Japanese camera industry, Zeiss discovered that it was essential to form an alliance with a Japanese maker. Asahi, maker of the Pentax, was engaged first; and it went as far as Zeiss designing a common lens mount, which became the Pentax K-mount after the two firms parted company. Then, an alliance was formed with Yashica, and a new line of Contax single-lens reflex cameras was born, starting from the RTS of 1975. Numerous models followed, which also included compacts, medium-format reflex cameras, and digital cameras.

Interestingly, rival Leica in the 1970s and 80s used a couple of West German Zeiss-designed wide-angle lenses for their own cameras. The 15 mm Hologon was the first super-wide lens on a Leica, and the Leica reflex had access to the 15 mm Distagon lens as part of the Leitz supplied range.

Kyocera took over Yashica in 1983 and continued to manufacture products under the Yashica and Contax brands. In the mid-90s came their Contax G1 with outstanding lenses and a little later the G2, both fully manual or automatic, The first zoom lens to a RF camera, lenses from 16 mm to 90 mm. However, by 2002 the company's film camera products were declining in sales, and its newer digital camera products failed to make serious inroads into the digital-photographic market. In 2005, Kyocera discontinued all photographic equipment manufacture, including the Contax brand in 2005, thus bringing the Contax story to a close.